Sway-A-Way 16-3/4" Total Length 4340 Chromoly 28 Spline Porsche 930 Solid Axles

Below, above the "add to cart" button there is a drop down menu for type of brakes. We want to know what type of brakes you're using to ensure that you have the appropriate spline length for your application.

Need a special length axle? We can cut any of our axles and regroove them for the clip. We charge per cut. Orders must be in before 12:00 Noon PST for same day shipping. Cut axles are NOT REFUNDABLE!


Sway-A-Way 16-3/4" Total Length 4340 Chromoly 28 Spline Porsche 930 Solid Axles

Suggested: $305.00 Kartek Price: $289.99

Sold As: 2 Porsche 930 Axles

Part Number: SAW24167

MFG Number: 2416-7




Sway-A-Way 16-3/4" Total Length 4340 Chromoly 28 Spline Porsche 930 Solid Axles
Sway A Way's American made 4340 Chromoly IRS axles are specially designed for the needs of today's off-road racers. The axles are machined from 4340 Chromoly steel alloy.

Specifications:
Material: 4340 Chromoly
Total Length: 16-3/4"
Clip To Clip Length: 16-3/8"
Spline Length Side A: 3"
Spline Length Side B: 3"

Measuring axle length for VW Stub axle, Micro Stub Axle, or Mid-Board Micro Stub Axle
  • Check your toe in/out wheel alignment.
  • Lift the hub up, so that if it did have an axle, the axle would be at zero degrees, parallel to the ground.
  • Measure from the BOTTOM of the drive flange cup on the transmission to the BOTTOM of the stub axle cup on the brakes. Reference Figure A
  • Subtract 1/4" to 3/8". That is your TOTAL axle length.
  • Check both sides of the vehicle. It is very common to have two different length axles.
  • Now use a PVC pipe as a mock-up axle. Cut grooves 1/4" down on either end into each end of the PVC for your clips. Install your CV joints and mock-up axle.
  • Lift the vehicle so the tires drop down to full droop. Depending on the type of CV joint you're using, will govern how much angle you can handle at full droop.
  • Grab your mock-up axle and make sure that you have 1/4" to 3/8" free play. Reference Figure B
  • If you have 1/4" to 3/8" free play at zero degrees and at full droop then you're perfect.
how do you measure IRS axle length for micro stub and midboard micro stub disc brakes?
Measuring axle length for Mid-Board Foater Hub or Out-Board Floater Hub
  • Check your toe in/out wheel alignment.
  • Install CVs on the transmission and on the hub side.
  • Lift the vehicle so the tires drop down to full droop. Reference Figure D
  • Measure from OUTSIDE edge of star to OUTSIDE edge of star. This is your clip to clip dimension. Add 1/2" and that is your TOTAL axle length dimension.
  • Check both sides of the vehicle. It is very common to have two different length axles.
  • Now use a PVC pipe as a mock-up axle. Cut grooves 1/4" down on either end into each end of the PVC for your clips. Install your CV joints and mock-up axle.
  • Grab your mock-up axle and make sure that you have 1/4" to 3/8" free play at full droop and at zero degrees. Reference Figure C and Figure D
  • If you have 1/4" to 3/8" free play at zero degrees and at full droop then you're perfect.
how do you measure IRS axle length for midboard floater hub and outboard floater hub disc brakes? 2416-7 2416.7 Chromoly Chrome-Moly Chrome Moly 4130

Related Parts